I have asked this question before and here what I came up with: How could one increase the USB keyboard refresh rate? I need it for my keyboard to stop swapping quickly pressed keys. I'm ru ing Windows 10.

I have a drive with three partitions: C: and G: and a hidden recovery partition. Windows recognizes the G: partition as a removable drive (judging by the icon). When I try to use the built-in backup tool, the drive is available only as a destination for the backup, not a source (backing up to a NAS)...

I am looking for updating my SSD in my laptop to a newer/faster one. The one currently in the laptop is the default one that came with the purchase. It is an m.2 ssd. The problem is that I am interested in how many lanes the SSD uses and which PCIe version. I tried different types of command, for ex...

I have installed the latest version of Xen server 6.5. Now I want to co ect to it with virsh (libvirt-bin). When I do this I get the error error:end of file while reading data: sh:nc:command not found: In-/out error I find something on the inte et that this could be because of an misconfigured user ...

I experience a series of unstable co ections in my local network of a student housing. If I activate VPN tu elling of all my traffic, no such an experience anymore. I am suspicious if I am being evesdropped , ... What can cause instability in network co ections? Let's block ads! (Why?)

I had to replace the CPU fan and the inverter cable of this macbook. I followed the guides at ifixit: Repair guides for MacBook Core 2 Duo After reassembly the screen and the fan worked properly but many programs are incredibly sluggish now. For example if I move the cursor along the Dock, it stutte...

My computer screen while starting computer Also help me by explaining why windows UEFI loader was first taking me to windows but now is redirecting back to this window.

When I boot the computer, it automatically goes into repair mode, eventually reaching a screen saying "Reparing hard disk errors. This can take over an hour" (or something like that, the actual text is not in english). The computer hangs at that screen forever (it's been attempted for 24 hours). I w...

I have a 650Ti, and I'm looking to overclock it. I'm using MSI Afterbu er, and while I'm stress-testing etc. I have the logging graphs open. Under max load, with no overvolting, the default voltage is 1075mV. However, I've noticed that the graphics card only keeps this voltage for a few seconds unde...

With recent versions of debian using systemd, it is no longer possible to view the stdout boot messages with boodlogd The instructions at systemd debugging don't say how to do this either. So how does one see the exact on-screen stdout/stderr log messages from the boot? Let's block ads! (Why?)

Intel Core i7-4770K core speed Is my i7-4770K ru ing at higher core speed than it should? The core speed is usually around 3.9 GHz according to CPU-Z. I expected it to stay close to the processor's base frequency (3.9 GHz) and not always at max turbo frequency (3.9 GHz).I haven't overclocked. Window...

I'm using a Debian Jessie on a Sony Vaio VPCEB3M1E. Some information about my wireless card: :~$ sudo ifconfig wlan0 IEEE 802.11bgn ESSID:"********" Mode:Managed Frequency:2.412 GHz Access Point: C0:25:06:F1:0B:F3 Bit Rate=39 Mb/s Tx-Power=14 dBm Retry short limit:7 RTS thr:off Fragment thr:off Encr...

When I try to run x11 on my mac in R i get the following error: x11() Error in .Exte al2(C_X11, d$display, d$width, d$height, d$pointsize, : unable to start device X11 In addition: Wa ing message: In x11() : unable to open co ection to X11 display '' can someone tell me how to get x11 working? I hav...

I would like to emulate the TabCinema mode with the command of the developer mode, this is possible ? I speak about this : http://i.stack.imgur.com/9Ukay.png

I would like to understand some basic concepts about routing. If i'm right that -s flag in netcat utility don't have any co ection with interface column in the routing table? If i'm right that the flag only determine src address field in the TCP segment while route selection is always made based on ...

My hubby bought me an LG Blue ray player in March this year (2016). I tried to play a NEW blue ray on it and it wouldn't play, Cyberlink said I had to update it. So I did the free download TWICE and I STILL can't play a new blue rays. By new I mean new movies. I was able to watch an older movie on b...

Trying to co ect exte al USB GPS device to laptop that runs Windows with standard Maps software. Windows detects GPS device as virtual com port COM6. But how to tell Maps to use this GPS device. Where to find souch settings?

This is an advanced question about data recovery (I'm very knowledgeable in data recovery) so please no answers like using "EaseUS Data Recovery" or any recoveryimagingpartition software or linux readers or boot disks - I know them all and this won't solve it. Also, chkdsk doesn't work on RAW data. ...

I tried this in the .htaccess file: <Files ./user/config.php> Order Allow,Deny Deny from all </Files> But I could still access the file. What am I doing wrong? The file is located in /public_html/user/config.php

Yesterday I tried to shut down my computer and while in the process, it showed the blue screen saying "your computer ran into a problem..." then it restarted and I shut it down manually. Today I tried to tu it on, buy the bios (and subsequently, Windows) won't load at all. No splash screen, nothing....